Neue GH701SS Bedienungsanleitung PDF herunterladen (Seite 10)

The hob should not be installed in a bed sitting room

with a volume of less than 20 m³. If it is installed in a

room of volume less than 5 m³ an air vent of effective

area of 100 cm² is required. If it is installed in a room of

volume between 5 m³ and 10 m³ an air vent of effective

area of 50 cm² is required, while if the volume exceeds

11 m³ no air vent is required.

However, if the room has a door which opens directly to

the outside no air vent is required even if the volume is

between 5 m³ and 11 m³.

If there are other fuel burning appliances in the same

room, B.S. 5440 Part 2 Current Edition, should be con-

sulted to determine the requisite air vent requirements.

For appliances installed in the Republic of Ireland

please refer to the NSAI- Domestic Gas Installation I.S.

813 Current Editions Table Four.

Location

The hob may be located in a kitchen, a kitchen/diner or

bed sitting room (with a volume greater than 20 m³), but

not in a bathroom or shower room.

The minimum distance combustible material can be fit-

ted above the hob in line with the edges of the hob is

400 mm. If it is fitted below 400 mm a space of 50 mm

must be allowed from the edges of the hob.

For appliances installed in the Republic of Ireland

please refer to NSAI- Domestic Gas Installation I.S 813

Current Edition Section 7- Permitted Locations of Appli-

ance.

Gas Connection

Warning! Any gas installation must be carried out

by a GAS SAFE REGISTER installer.

Make sure that, once the hob is installed, it is easily ac-

cessible for the engineer in the event of a breakdown.

The manufacturer will not accept liability, should the

above instructions or any of the other safety instructions

incorporated in this instruction booklet be ignored.

On the end of the shaft, which includes the G 1/2" threa-

ded elbow, adjustment is fixed so that the washer is fit-

ted between the components as shown in the diagram.

Screw the parts together without using excessive force.

ABC

A) End of shaft with nut

B) Washer

C) Elbow

Connection to the gas supply should be with either rigid

or semi-rigid pipe, i.e. steel or copper.

The connection should be suitable for connecting to R

1/2 (1/2 BSP male thread).

When the final connection has been made, it is essential

that a thorough leak test is carried out on the hob and

installation.

Make sure that the main connection pipe does not exert

any strain on the hob.

If you use flexible metal pipes make sure that they

agree to ISO 10380 and ISO 10807 standards. Be care-

ful they do not come in touch with mobile parts or they

are not squeezed. Also be careful when the hob is put

together with an oven.

Important! It is important to install the elbow correctly,

with the shoulder on the end of the thread, fitted to the

hob connecting pipe.

Important! Failure to ensure the correct assembly will

cause leakage of gas.

Important! Make sure that the gas supply pressure of

the appliance obeys the recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes (copper

with mechanical end).

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors and

replace them with the ones which are necessary

for the type of gas you use (see table in "Technical

Information" chapter).

4. Assemble the parts, follow the same procedure

backwards.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Neue GH701SS Bedienungsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Neue GH701SS